Note for the NDI License Key:
- All sales are final. Licenses are non-refundable and non-transferable.
- The license key will be sent via email after purchase.
- Please note that each NDI license key is specific to one NexiGo P620 camera.
- Click here to access the guide for using NDI with the P620 camera.
FAQ
Setting the Camera Frequency:
To set the camera frequency to one of your remote channels, hold the remote close to your camera and press the following sequence of buttons. Note that you can only control the camera(s) on the channel that your remote is currently using.
【*】>【＃】>【I】: Press these three buttons in sequence to set the camera
frequency to No.1.
【*】>【＃】>【II】: Press these three buttons in sequence to set the camera
frequency to No.2.
【*】>【＃】>【III】: Press these three buttons in sequence to set the
camera frequency to No.3.
【*】>【＃】>【IV】: Press these three buttons in sequence to set the
camera frequency to No.4
*For a multi-camera setup, it is recommended to use numbered stickers to label the frequency of each camera for quick identification.
Switching Between Remote Channels:
Press and hold one of the numeral buttons (l, ll, lll, or lV) for four seconds to switch between camera channels. The red indicator light will start blinking rapidly. Once the blinking slows, the remote will be able to control the camera at the corresponding frequency.
【I】: Press and hold for at least four seconds to switch the remote channel to No.1.
【II】: Press and hold for at least four seconds to switch the remote channel to No.2.
【III】: Press and hold for at least four seconds to switch the remote channel to No.3.
【IV】: Press and hold for at least four seconds to switch the remote channel to No.4.
*The remote control channel and camera frequency both default to No.1. The remote channel and the camera frequency must beset to be the same number in order for the remote to control the camera.
1. Indicator Light: A red indicator light will flash each time you press a button. lf it doesn't light up, check the batteries and try again.
2. Power Button: Press the red power button to turn the webcam on or off.
3. Camera Mode Button: Press to switch between the available camera modes: Default, Norm, Clarity and Soft.
*The camera mode list here is for reference only. Available modesmay differ depending on your current firmware.
4. Rotation Direction Switch: Press to swap between clockwise and counterclockwise camera panning.
5. No Function
6. Home Button: Press to reset the camera view to its default position. While in the OSD menu, press to select.
7. Arrow Buttons: Press to pan or tilt the camera view, hold to adjust faster. While in the OSD menu, use the【↑】and【↓】 arrows to navigate the menu and use the【←】and 【→】arrows to make adjustments to the settings.
*Please close the OSD menu before using the electronic pan / tilt / zoom function.
8. No Function
9. Auto / Manual Focus Switch: Press to switch between autofocus mode and manual focus mode.
10. Menu Button: Press the Menu button once to open or close the on-screen display (OSD) menu. In the OSD menu, you can adjust color and exposure settings using the following controls.
● Use the Arrow buttons to navigate through the menu.
● Use the Home button to open a submenu or select an option.
● Use the Menu button to return to the previous page (if you are in a submenu), or to close the menu (if you are in the main menu).
11. Near / Far Focus Button:
Press Focus + to move the focal point farther away.
Press Focus - to move the focal point closer.
*This function is only possible while in manual focus mode. The focus buttons have no function while in autofocus mode.
12. Preset Button: Use to create a positional preset by performing the following steps.
● Adjust the zoom, pan, and tilt to your desired position. Note that presets will only save pan, tilt, and zoom settings and NOT any light or color settings.
● Press the Preset button once to enter the preset writing mode.
● Press one of the Numbered buttons (0-6, 1-V) to save the preset to that number. This will override any presets that have previously been saved to that number.
● To recall a preset at any time, press its corresponding number
13. Zoom+ / - Buttons: Press to zoom in (+) or out (-) on the video. Hold to adjust faster.
14. Numbered Buttons (0-6, I-IV): Use the digits (0-6) and numerals (l-V) to set and recall preset positions. Use the numerals (l-V) to set a remote control or camera address for a multi-cam setup.
Setting the Camera Frequency:
To set the camera frequency to one of your remote channels, hold the remote close to your camera and press the following sequence of buttons. Note that you can only control the camera(s) on the channel that your remote is currently using.
【*】>【＃】>【I】: Press these three buttons in sequence to set the camera
frequency to No.1.
【*】>【＃】>【II】: Press these three buttons in sequence to set the camera
frequency to No.2.
【*】>【＃】>【III】: Press these three buttons in sequence to set the
camera frequency to No.3.
【*】>【＃】>【IV】: Press these three buttons in sequence to set the
camera frequency to No.4
*For a multi-camera setup, it is recommended to use numbered stickers to label the frequency of each camera for quick identification.
Switching Between Remote Channels:
Press and hold one of the numeral buttons (l, ll, lll, or lV) for four seconds to switch between camera channels. The red indicator light will start blinking rapidly. Once the blinking slows, the remote will be able to control the camera at the corresponding frequency.
【I】: Press and hold for at least four seconds to switch the remote channel to No.1.
【II】: Press and hold for at least four seconds to switch the remote channel to No.2.
【III】: Press and hold for at least four seconds to switch the remote channel to No.3.
【IV】: Press and hold for at least four seconds to switch the remote channel to No.4.
*The remote control channel and camera frequency both default to No.1. The remote channel and the camera frequency must beset to be the same number in order for the remote to control the camera.
